Starter For Honda Accord 2013 2014 2015 2016 / 2015 2016 CRV CR-V 2.4L Automatic

Description

Product Information:
Unit Type: Starter
Part Type: UNIT
Voltage: 12
Rotation: CW
Teeth: 9
KW: 1.6
Starter Type: PMGR
Interchange Part Number:
Honda: 31200-5A2-A51,312005A2A52,31200-5A2-A52,312005A2A51
Lester: 10914
Mitsuba: SM-74009
Remy Reman: 16201
Fitment Information:
MAKE     TYPE     MODEL     YEAR      ENGINE
Honda Auto and Light Truck Accord L4 2013-2016 2.4L
Honda Auto and Light Truck CR-V L4 2015-2016 2.4L
How to Install a Car Starter:
Starter For Honda Accord 2013 2014 2015 2016 / 2015 2016 CRV CR-V 2.4L Automatic
Product Information:
Unit Type: Starter
Part Type: UNIT
Voltage: 12
Rotation: CW
Teeth: 9
KW: 1.6
Starter Type: PMGR
Interchange Part Number:
Honda: 31200-5A2-A51,312005A2A52,31200-5A2-A52,312005A2A51
Lester: 10914
Mitsuba: SM-74009
Remy Reman: 16201
Fitment Information:
MAKE     TYPE     MODEL     YEAR      ENGINE
Honda Auto and Light Truck Accord L4 2013-2016 2.4L
Honda Auto and Light Truck CR-V L4 2015-2016 2.4L
How to Install a Car Starter:
There’s never a convenient time for your vehicle’s starter to fail. A car starter's job is to kick over the engine in your car so your vehicle starts.When you find yourself with a vehicle that won’t start, there are a number of a number of issues that may be the culprit,but once you’ve narrowed it down to a faulty starter, you can replace it using just common hand tools.
Part 1: Removing a Bad Starter
(1).Disconnect the battery.
You will not need to remove the positive cable on the battery.
Always disconnect the battery before servicing the electrical system in your vehicle.
(2).Jack up the vehicle if need be.
Ensure you jack the vehicle up on firm, level ground.
(3).Locate the starter.
The smaller cylinder attached to the starter is the starter solenoid.
A wire should run directly from the positive terminal on the battery or from the fuse box under the hood to the top terminal on the starter solenoid.
(4).Disconnect the wiring to the solenoid.
In some cases, it may just be clips you need to disconnect for the wiring.
On some starters, you will need to loosen bolts or screws that hold the wires in place.
(5).Remove the starter retaining bolts then the starter.
Be sure to use the correct size socket, otherwise you risk damaging the bolts.
(6).Compare the new starter to the old one.
Slide the starter into place.
If the two starters don’t look mostly identical, it may not be the correct starter for your vehicle.
New starter solenoids often come with four terminals, but can be used with only two.
Part 2: Installing a New Starter
(7).Insert the starter retainer bolts.
If the bolt does not thread properly, unscrew it and try again.
Make sure the bolts are tight so they can’t vibrate loose while the engine is running.
(8).Connect the wiring to the starter solenoid.
With the starter secured in place, reconnect the wiring you disconnected from the old starter onto the terminals on the new one. If your new solenoid has four terminals but your old one had two, only utilize the top and bottom terminal on the new solenoid. If your old one had four and the new one does as well, connect them to the same terminals they were connected to on the old one.
(9).Reconnect the battery.
With the starter installed and wired, reconnect the black cable to the negative terminal on the battery and tighten it in place. Insert the key into the ignition and attempt to start the vehicle.
If the vehicle fails to start with the new starter in place, ensure the battery is fully charged.
(10).Listen to the vehicle as you attempt to start it.
As you turn the key in the ignition, listen for the sounds the engine makes to help determine if you have an issue with your starter. If the engine makes no sound whatsoever, or you hear only a faint clicking, it may be because there isn’t enough power reaching the electric starter motor.
(11).Ensure the battery terminals are clean and secure.
Charge your vehicle’s battery.
A weak connection from the battery can prevent the engine from starting.
Wear gloves when cleaning battery terminals to avoid getting battery acid on your skin.
If you suspect the battery may simply be low on power, try charging it using either a trickle charger or another vehicle to jump start it. Be sure to connect the red cable to the positive terminal on each vehicle and the black to the negative.
(12).Check to see the starter solenoid is bad.
If the test light does not light up, it means power is not reaching the starter motor due to a faulty solenoid or a dead battery.
If the test light does light up, it means the solenoid is good, but the starter itself may have failed.
Item Specifics
Brand
top-liftsupport
Manufacturer Part Number
TL11268401S
Interchange Part Number
312005A2A52 SM-74009 16201 31200-5A2-A51
Other Part Number
10914 31200-5A2-A52 312005A2A51
Compatibility
Starter For Honda
Warranty
1 Year
Device Type
Direct Replacement
Condition
New
Surface Finish
New Quality
Part Type
UNIT
Unit Type
Starter
Voltage
12
Rotation
CW
Teeth
9
KW
1.6
Starter Type
PMGR
Weight
2.985kg
Package
26.00(L)*15.00(W)*15.00(H)CM
Number of Pieces
1
Non-Domestic Product
No
Custom Bundle
No
Modified Item
No
Position
Front
Item Specifics
Brand
top-liftsupport
Manufacturer Part Number
TL11268401S
Interchange Part Number
312005A2A52 SM-74009 16201 31200-5A2-A51
Other Part Number
10914 31200-5A2-A52 312005A2A51
Compatibility
Starter For Honda
Warranty
1 Year
Device Type
Direct Replacement
Condition
New
Surface Finish
New Quality
Part Type
UNIT
Unit Type
Starter
Voltage
12
Rotation
CW
Teeth
9
KW
1.6
Starter Type
PMGR
Weight
2.985kg
Package
26.00(L)*15.00(W)*15.00(H)CM
Number of Pieces
1
Non-Domestic Product
No
Custom Bundle
No
Modified Item
No
Position
Front
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1. Orders processed within 24 hours of payment verification.
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class/UPS/Fedex.... Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
New List Item
For Motorcycle LED Projector 7'' Headlight and 4.5'' Passing Lights
USD 89.87
Oxygen 02 O2 Sensor For 2004-2009 Mitsubishi Galant 3.8L Upstream wire 4
USD 16.27
Fits 01-09 Toyota Prius Heater Blower Motor with Fan Cage 8710347020 Front HVAC
USD 46.09
Fits 05-07 Chevrolet Equinox Pontiac Torrent Front Steering Kit Ball Joint x6
USD 69.27
Power Window Regulator Rear Left fit for 2006-2013 Chevy Impala with Motor
USD 51.99
Hot Item
2 Rear Liftgate Hatch Tailgate Lift Supports Struts For Town & Country 2001-2007
USD 22.39
2 Rear Trunk Liftgate Tailgate Hatch Lift Support For 99-04 Suburban Tahoe Yukon
USD 18.19
For 1997-2001 Jeep Cherokee 2* Rear Tailgate Hatch Gas Lift Supports Strut Shock
USD 22.99
Qty(2) For Honda Accord 2003-2007 Front Hood Lift Supports Gas Prop Struts Shock
USD 17.19
2 Front Hood Lift Supports Struts Struts Gas Spring For 2002-2007 Jeep Liberty
USD 15.89
Shop Category
Store Home
Body Kits
◈  Front Bumper Lip
Lift supports
Wheel hub
remote key
Exhaust System Parts
Mirrors
Wheel Spacers
Leveling Lift Kit
Cylinder Head Gasket Sets
AC Compressor
Shocks & Struts
CV axle
Brake Pads & Rotors
◈  Brake Pads
◈  Brake Rotors
◈  Brake Pads and Rotors
Fuel injectors
Coilover
Air Suspension
Complete Strut
Cylinder Piston Gasket Sets
Car Tools
Valve Cover
Door Lock Actuator
Power Steering Pump
Variable Timing Solenoid (VVT)
Electric Water Pump
Fuel Tank Pipe
Timing Chain Kits
Timing Belt Kits
Water Pumps
Strut Tie Bar
Throttle Body
Harmonic Balancer
Oil Pan
Intake Manifold
EGR Valve
Radiator Coolant Tank
HVAC
ATV Rear Wheel Axle
Car Antenna
ABS Wheel Speed Sensor
Spoilers & Wings
Thermostat Housing
Regulator Rectifier
Oil Cooler
Starter Relay
Knock Sensor
Turbocharger
Parking sensor
Window Switch
Window Regulator
Ignition coil
Detection tools
Crankshaft Position Sensor
Camshaft Position Sensor
MAP Sensor
Oil Pressure Sensor
Throttle Position Sensor
Stator
Catalytic Converter
Transfer Case Shift Motor
Secondary Air Injection Pump
Running Board Motor
Clutch Slave Cylinder
Consoles & Parts
Towing & Hauling
Door handles
LED Headlight
Bumper
Roof rack
Tire Pressure Gauge
Steering Rack
starter
Wiring Harness
Spark Plug Ignition Wire
Engine Mount
Glow Plug
Air Cleaner Filter Box
Pressure Tester Gauge
Jack Stands
Wheel Lug
Sun Visor
alternator
ATV Brake Caliper
Interior LED Light
ignition distributor
Car Carburetor
EGR Tube Pipe
Air Intake Hose
Cold Air Intake Kit
Heater Control Valve
Clock Spring
Steering U-Joint
Fuel Cell Tank
Height Level Sensor
Temperature Sensor
Driveshaft
Vacuum Actuator
Ballast module
Rubber Seal Strip
Nerf Bars
ATV Brake Master Cylinder
4WD Actuator
Fuel Injector Wiring Harness
Oil Filter Wrench
Oil Fuel Hose Line
LED headlight Assembly
headlight motorcycle
water Pump Impeller
A/C Expansion Valve
Wheel Stem Air Valve Cap
Rocker Arm
Hydraulic Lifter&Roller Lifter
Oxygen Sensors
Sensor-8
tire cover
CV axle+Brake Pads/Rotors
Steering Shaft
transmission filter
transmission kit
Fuel Pumps
Windshield Wiper Motor
Jeep9
CDI BOX
Proportioning Valve
suspension kit
Strut Mount Kit
Crankshaft Pulley
4 Pcs wheel hub bearing
Alternator Bracket Kit
Fender Flares
jumper cable
ATV Tires
Tonneau Cover
Window Visor
Bug Shield
dash cover
tire pressure sensor
fastener
Switch Panel
vehicle speed sensor
Pillar Posts
Cargo Cover
Hub Caps
fog lights
ATV Ignition Switch
Windshield Outer Trim
Fuse Holder Box
Suspension+Strut+Bearing
Rear View Camera
Drop Spindle Lowering Kit
Car Seat Cover
Window Louver Cover
Motorcycle Link Pipe
Blow Off Valve
winch
AC Compressor Control Valve
leveling kit + struts shocks
Dash Cover
Radiator Shutter
Other
Starter For Honda Accord 2013 2014 2015 2016 / 2015 2016 CRV CR-V 2.4L Automatic
Product Information:
Unit Type: Starter
Part Type: UNIT
Voltage: 12
Rotation: CW
Teeth: 9
KW: 1.6
Starter Type: PMGR
Interchange Part Number:
Honda: 31200-5A2-A51,312005A2A52,31200-5A2-A52,312005A2A51
Lester: 10914
Mitsuba: SM-74009
Remy Reman: 16201
Fitment Information:
MAKE     TYPE     MODEL     YEAR      ENGINE
Honda Auto and Light Truck Accord L4 2013-2016 2.4L
Honda Auto and Light Truck CR-V L4 2015-2016 2.4L
How to Install a Car Starter:
There’s never a convenient time for your vehicle’s starter to fail. A car starter's job is to kick over the engine in your car so your vehicle starts.When you find yourself with a vehicle that won’t start, there are a number of a number of issues that may be the culprit,but once you’ve narrowed it down to a faulty starter, you can replace it using just common hand tools.
Part 1: Removing a Bad Starter
(1).Disconnect the battery.
You will not need to remove the positive cable on the battery.
Always disconnect the battery before servicing the electrical system in your vehicle.
(2).Jack up the vehicle if need be.
Ensure you jack the vehicle up on firm, level ground.
(3).Locate the starter.
The smaller cylinder attached to the starter is the starter solenoid.
A wire should run directly from the positive terminal on the battery or from the fuse box under the hood to the top terminal on the starter solenoid.
(4).Disconnect the wiring to the solenoid.
In some cases, it may just be clips you need to disconnect for the wiring.
On some starters, you will need to loosen bolts or screws that hold the wires in place.
(5).Remove the starter retaining bolts then the starter.
Be sure to use the correct size socket, otherwise you risk damaging the bolts.
(6).Compare the new starter to the old one.
Slide the starter into place.
If the two starters don’t look mostly identical, it may not be the correct starter for your vehicle.
New starter solenoids often come with four terminals, but can be used with only two.
Part 2: Installing a New Starter
(7).Insert the starter retainer bolts.
If the bolt does not thread properly, unscrew it and try again.
Make sure the bolts are tight so they can’t vibrate loose while the engine is running.
(8).Connect the wiring to the starter solenoid.
With the starter secured in place, reconnect the wiring you disconnected from the old starter onto the terminals on the new one. If your new solenoid has four terminals but your old one had two, only utilize the top and bottom terminal on the new solenoid. If your old one had four and the new one does as well, connect them to the same terminals they were connected to on the old one.
(9).Reconnect the battery.
With the starter installed and wired, reconnect the black cable to the negative terminal on the battery and tighten it in place. Insert the key into the ignition and attempt to start the vehicle.
If the vehicle fails to start with the new starter in place, ensure the battery is fully charged.
(10).Listen to the vehicle as you attempt to start it.
As you turn the key in the ignition, listen for the sounds the engine makes to help determine if you have an issue with your starter. If the engine makes no sound whatsoever, or you hear only a faint clicking, it may be because there isn’t enough power reaching the electric starter motor.
(11).Ensure the battery terminals are clean and secure.
Charge your vehicle’s battery.
A weak connection from the battery can prevent the engine from starting.
Wear gloves when cleaning battery terminals to avoid getting battery acid on your skin.
If you suspect the battery may simply be low on power, try charging it using either a trickle charger or another vehicle to jump start it. Be sure to connect the red cable to the positive terminal on each vehicle and the black to the negative.
(12).Check to see the starter solenoid is bad.
If the test light does not light up, it means power is not reaching the starter motor due to a faulty solenoid or a dead battery.
If the test light does light up, it means the solenoid is good, but the starter itself may have failed.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 10 days as auction ended or order might be delayed.
1. Orders processed within 24 hours of payment verification.
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class/UPS/Fedex.... Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Copyright of Top-liftsupport
. All rights reserved.